Forklift Carburetors

A carburetor mixes fuel and air together for an internal combustion engine. The device has an open pipe called a "Pengina" or barrel, through which the air passes into the inlet manifold of the engine. The pipe narrows in part and afterward widens again. This particular format is called a "Venturi," it causes the airflow to increase speed in the narrowest part. Under the Venturi is a butterfly valve, which is also called the throttle valve. It works to control the air flow through the carburetor throat and regulates the amount of air/fuel mixture the system will deliver, which in turn controls both engine power and speed. The throttle valve is a rotating disc which can be turned end-on to the flow of air to be able to barely limit the flow or rotated so that it can totally block the air flow.

Generally connected to the throttle by way of a mechanical linkage of joints and rods (every so often a pneumatic link) to the accelerator pedal on a vehicle or piece of material handling device. There are small holes located on the narrow section of the Venturi and at several areas where the pressure would be lowered when running full throttle. It is through these holes where fuel is introduced into the air stream. Specifically calibrated orifices, referred to as jets, in the fuel channel are accountable for adjusting fuel flow.

Click to Download the pdf

Forklift Parts in Fresno

Alternators

An alternator is a machine which changes mechanical energy into electric energy. It does this in the form of an electrical current. In essence, an AC electric generator could be labeled an alternator. The word usually refers to a rotating, small machine driven by automotive and other internal combustion engines. Alternators which are situated in power stations and are powered...

More

---

Brakes

A brake in which the friction is supplied by a set of brake shoes or brake pads which press against a rotating drum shaped unit referred to as a brake drum. There are several particular differences among brake drum kinds. A "brake drum" is normally the definition provided if shoes press on the inner exterior of the drum. A "clasp...

More

---

Carriage Rollers

Specially designed bearings known as carriage rollers are regularly seen on lift masts because they enable them to operate better in difficult environmental surroundings. The typical lift mast is often subject to frequent oscillations, shocks, static loads, and vibrations and high dynamics. This apparatus is regularly exposed to environmental influences like for instance heat, dust, cold, aggressive ambient air, moisture...

More

---

Carriages and Carriage Parts

Rated by the fork carriage lifting capacity, there are actually four sizes of hook type blade carriages. The hook type fork carriages have been standardized. The carriage bar spacing utilized for Class 1 is around thirteen inches and the Class 1 carriage is rated to hold cargo as much as 2000lbs. The Class 2 carriage is rated to carry cargo...

More

---

Control Valves

Automatic control systems were first developed more than two thousand years ago. The ancient water clock of Ktesibios in Alexandria Egypt dating to the third century B.C. is thought to be the very first feedback control machine on record. This clock kept time by means of regulating the water level in a vessel and the water flow from the vessel....

More

---

Controllers

Lift trucks are obtainable in several different models which have various load capacities. Most standard forklifts utilized inside warehouse environment have load capacities of one to five tons. Larger scale units are utilized for heavier loads, like for instance loading shipping containers, may have up to 50 tons lift capacity. The operator could use a control so as to lower...

More

---

Differentials

A mechanical device capable of transmitting rotation and torque through three shafts is known as a differential. Every now and then but not always the differential will utilize gears and would operate in two ways: in cars, it receives one input and provides two outputs. The other way a differential works is to put together two inputs in order to...

More

---

Drive Axles

A forklift drive axle is a piece of equipment which is elastically fastened to a vehicle framework using a lift mast. The lift mast is connected to the drive axle and could be inclined around the axial centerline of the drive axle. This is accomplished by no less than one tilting cylinder. Forward bearing parts along with back bearing parts...

More

---